[BFix] Re: [socalbroncos] BURN THE FLAG (not really-just wanted to get your attention -have serious ?? on my 5.8 MAF tho)

[ken]

If you wanted attention, you did get that.

Our son puts himself in the middle of harms way to give you the right to 
say, or even do what you suggested.  Believe me, you made no friends here 
with that subject line.

If you never get your Bronco fixed, it will be sooner than I'd like to see. 
Take your Bronco to Iraq, where our son went, to insure your rights, and see 
if you can get help from the flag burners there.

ken  - WK4KMW
1970 Sport
Modified by: BC Broncos, STaK 4X4, and Ralph Bouknight,
(With a little help from me)


----- Original Message ----- 
From: "Dan" <bronco at barrhome.net>
To: "Broncofix" <bfix at broncofix.com>; <socalbroncos at yahoogroups.com>; 
<sales at rjminjectiontech.com>
Sent: Saturday, May 03, 2008 4:55 PM
Subject: [socalbroncos] BURN THE FLAG (not really-just wanted to get your 
attention -have serious ?? on my 5.8 MAF tho)


>
>
> Okay - I posted this a while ago and got some feedback but it has left me
> still scratching my head.
>
> My MAF is from a '95 5.8 california truck.  This was an EEC-IV OBDI
> computer.  It is an oval connector but it is not the same as the oval
> connector on the 5.0 harnesses.  Go here for pics of the MAF and the RJM
> harness:
>
> http://www.barrhome.net/Bronco%20Blog/2E7B9812-AAF0-4938-945C-7BF2CA753FD9.h
> tml
>
> The harness in the pic is actually being held upside down.  The RJM 
> harness
> will not plug into the MAF.  I would have to shave off all tabs and turn 
> the
> plug upside down to actually fit.  The spade terminals are offset just
> slightly to one side of the oval and the MAF is offset to the opposite 
> side
> as the harness.
>
> Ryan has some other pigtails for other MAFs on his site but none match 
> mine.
>
> The way I see it, I have 3 options:
>   1.  Buy a cheap 5.0 55mm MAF on eBay and transfer the electronics to 
> this
> housing (hoping they are compatible)
>   2. Cut the pigtail out of the original harness and try to figure out
> which wire goes to where.  Kinda sucks though because then this thing 
> would
>   3.  Buy  new MAF  (not really wanting to spend the $$ though...)
>
> Anybody know if the 5.0 MAF electronics will fit on this housing?  If so,
> anyone have an old MAF they will part with for cheap?
>
> That would be the best option in my opinion so that the rig is 100% '89-93
> 5.0 EEC compatible.
>
> Thanks for any and all guidance.
>
>
> -- 
> Dan
> Alpharetta, GA
>
> '77 EB, C4, BC Bronco's 3.5" suspension lift, Bilstein 7100's front & 
> 5100's
> rear, BC Bronco's F150 Tie Rod Over and a very tired oil burning 302
> awaiting the SEFI 5.8.
>
>
>
>
> ------------------------------------
>
> To learn more about the socalbroncos group, please visit
> http://groups.yahoo.com/group/socalbroncosYahoo! Groups Links
>
> <*> To visit your group on the web, go to:
>    http://groups.yahoo.com/group/socalbroncos/
>
> <*> Your email settings:
>    Individual Email | Traditional
>
> <*> To change settings online go to:
>    http://groups.yahoo.com/group/socalbroncos/join
>    (Yahoo! ID required)
>
> <*> To change settings via email:
>    mailto:socalbroncos-digest at yahoogroups.com
>    mailto:socalbroncos-fullfeatured at yahoogroups.com
>
> <*> To unsubscribe from this group, send an email to:
>    socalbroncos-unsubscribe at yahoogroups.com
>
> <*> Your use of Yahoo! Groups is subject to:
>    http://docs.yahoo.com/info/terms/
>
>
>