[BFix] Trans Help

[FRANK w]

This is for the wifes Bronco. It will see a lot of street time. Should I swap the thin one to the top or will it be fine with the thick on the top? When I took the OEM Bronco spacers out the thin one was on the top. I think someone swaped them out as they look to have been there a long time.

Frank
  ----- Original Message ----- 
  From: Erik Christensen<mailto:cat44 at telus.net> 
  To: FRANK w<mailto:bbronko at msn.com> ; bfix<mailto:mail at broncofix.com> ; ebml<mailto:ebml at broncofix.com> 
  Sent: Sunday, May 04, 2008 6:16 PM
  Subject: Re: [BFix] Trans Help


  supposed to be thick on top, but switching it will improve rear driveline angle (at the expense of front).
    ----- Original Message ----- 
    From: FRANK w<mailto:bbronko at msn.com> 
    To: bfix<mailto:mail at broncofix.com> ; ebml<mailto:ebml at broncofix.com> 
    Sent: Sunday, May 04, 2008 4:33 PM
    Subject: Re: [BFix] Trans Help


    I found a pic here. It shows the thick one on top.  http://www.tomsbroncoparts.com/6070.php<http://www.tomsbroncoparts.com/6070.php>  I think I will try it this way.

    Frank 
      ----- Original Message ----- 
      From: FRANK w<mailto:bbronko at msn.com> 
      To: Joe Lougee<mailto:71broncoman at prodigy.net> 
      Cc: bfix<mailto:mail at broncofix.com> ; ebml<mailto:ebml at broncofix.com> 
      Sent: Sunday, May 04, 2008 3:33 PM
      Subject: Re: [BFix] Trans Help


      Thanks Joe,

      I got some poly trans mount bushings. Does the thick one go on top or below the transfer case crossmember. The thin one is about 3/4" thick and the thick one is about 1 1/16 " thick. Thanks again. 

      Frank

        ----- Original Message ----- 
        From: Joe Lougee<mailto:71broncoman at prodigy.net> 
        To: FRANK w<mailto:bbronko at msn.com> 
        Cc: bfix<mailto:mail at broncofix.com> ; ebml<mailto:ebml at broncofix.com> 
        Sent: Sunday, May 04, 2008 2:29 PM
        Subject: Re: [BFix] Trans Help


        Assuming you're talking about the rubber bumper that's on the stock 
        cross-member, it goes toward the back of the EB.  IOW, it should touch 
        (or close to) the transfer case.
        Joe


        FRANK w wrote:
        > Hello,
        >  
        > I am now installing a trans back into my Bronco. It has been a long 
        > long time so here is the question. Does the rubber transfer case 
        > bumper go to the front or the rear of the Bronco. Thanks for any help.
        >  
        >  
        > Frank 
        > ------------------------------------------------------------------------
        >
        > _______________________________________________
        > bfix mailing list
        > bfix at broncofix.com<mailto:bfix at broncofix.com>
        > http://broncofix.com/mailman/listinfo/bfix<http://broncofix.com/mailman/listinfo/bfix>
        >   

      _______________________________________________
      bfix mailing list
      bfix at broncofix.com
      http://broncofix.com/mailman/listinfo/bfix



----------------------------------------------------------------------------


    _______________________________________________
    bfix mailing list
    bfix at broncofix.com
    http://broncofix.com/mailman/listinfo/bfix
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://www.broncofix.com/pipermail/bfix/attachments/20080504/0aef09a4/attachment.html