[BFix] Leaking injectors???

[Ken]

Well, just got another call from him and he has all 8 spark plugs out and turned the key on to push out any fluids that may be in the cylinders and after only a few cranks he now has gas running out of all 8 spark plug holes!  This is getting interesting and I'm stuck at work and can't go look at it.
 
:o\

 
 68 EB 5.0L / ZF 
35" BFGs / 3" Lift
4.56 ARB Front & Rear



----- Original Message ----
From: Pat <kelpy at bellsouth.net>
To: Ken <broncokak at yahoo.com>; bfranklinisg at earthlink.net
Cc: mail at broncofix.com
Sent: Monday, May 5, 2008 8:59:54 PM
Subject: Re: [BFix] Leaking injectors???


The pump only runs when the engine is running or cranking or for a couple of seconds after the key is turned to run - it won't keep cycling because of a leaking injector.
 
Pat
----- Original Message ----- 
From: Ken 
To: bfranklinisg at earthlink.net 
Cc: mail at broncofix.com 
Sent: Monday, May 05, 2008 7:57 PM
Subject: Re: [BFix] Leaking injectors???

Well, he just called and said he drained the oil and it has gas in it. He is going to check his return line and make sure it is not plugged up. It is all new line except for where it enters the tank. I have a fuel pressure gage I'm going to take over and see what he has on the Hi-pressure side as well. 
 
Oh ya...he now has some new push rods too.

Ken
 
68 EB 5.0L / ZF 
35" BFGs / 3" Lift
4.56 ARB Front & Rear



----- Original Message ----
From: "bfranklinisg at earthlink.net" <bfranklinisg at earthlink.net>
To: Ken <broncokak at yahoo.com>
Sent: Monday, May 5, 2008 6:17:39 PM
Subject: RE: [BFix] Leaking injectors???


If they did fill up with gas then yep it could bend a rod. If he left the key in the on position and his injectors are leaking then the pump would continue to cycle as the pump loses pressure.  In theory it sounds good but I have never heard of it happening.
 
Ben
 
 
----- Original Message ----- 
From: Ken 
To: mail at broncofix.com
Sent: 5/5/2008 4:55:21 PM 
Subject: [BFix] Leaking injectors???

OK, I just got a call from my buddy I'm helping swap an 88 5.0L into his EB. The thing has been running good after we got the vacuum line hooked up to the MAP sensor. Last night he went to start it and wouldn't roll over. The old battery he has in it is pretty tired so he tried to start it again and it blew a "heave mist" as he said out the throttle body. On the 3rd try it did start but now ticks like crazy! He pulled some plugs and found them soaked with gas. Further investigations found 7 of the 8 intake push rods are now bent. He has rechecked his timing and it is OK. He is thinking the injectors may be leaking and filling the cylinder with gas. Could this bend a push rod? One other note. He *thinks* he may have left the key in the run position after the engine stalled out on him earlier in the day. Would that allow the pump to keep building pressure at all? 
 
 
TIA for any suggestions on where to look next.
 
Ken
________________________________
Be a better friend, newshound, and know-it-all with Yahoo! Mobile. Try it now. 
________________________________
Be a better friend, newshound, and know-it-all with Yahoo! Mobile. Try it now.

__________ NOD32 3076 (20080505) Information __________

This message was checked by NOD32 antivirus system.
http://www.eset.com

________________________________
_______________________________________________
bfix mailing list
bfix at broncofix.com
http://broncofix.com/mailman/listinfo/bfix



__________ NOD32 3076 (20080505) Information __________

This message was checked by NOD32 antivirus system.
http://www.eset.com



      ____________________________________________________________________________________
Be a better friend, newshound, and 
know-it-all with Yahoo! Mobile.  Try it now.  http://mobile.yahoo.com/;_ylt=Ahu06i62sR8HDtDypao8Wcj9tAcJ
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://www.broncofix.com/pipermail/bfix/attachments/20080505/c476cd99/attachment.html